The filling and sealing machine should clean the surface‌₩  of the machine table, the ¶♦♣bottom plate and the double rocker o∏αf the upper mold, the pipe groove, the pins in  ‌ε☆the lower mold and the co★€rrect positioning rod (the poγ± ‌wer must be cut off t<↕✔o repair the normal tempε₽✘erature). The position of the transmission ©φsystem, such as the upper mol≥☆d double seesaw, the pressure rod rolling bearinδ∞g, the rack and the positi★¶÷♣oning pin, the slide ≤•♣rail, etc., should be added with unsalte&‍★φd butter. Ensure equipment performance metr₽✘ics on time. The method of clearing the tooth ¶•knife: first use a co​•tton ball to plug the 2 drain holes of the l§∞≈ower mold, pour the boiling waλαter into the pipe groove of the upper moα★₹ld, fill the double rocker of the upp₩♠er mold, and send it to the d↑©¶σouble rocker of the upper mol€←γd in time, and press the bottom. Die, soak the to☆π€oth knife for several minutes until the rπ§₩↓emoval cut-off, and continue for several times.

The filling and sealing®δ machine is composed of a cleaning part a≈∑®εnd a glueing part, and ÷≥α¥its characteristics depend on φ&the above-mentioned cleaning part consisα‍ting of nine parts. The transmission∏↔✘  chain is connected with th↑π≤e rotating and shaking mechanical equipment of th"→e transmission gear and its follow-up sl<→ ‍eeve. An L-shaped supportλ&¥ bar is placed in the rotating an∞↓‌'d shaking structure of the trans•π₽φmission gear. The type sprocket chain pr≤∑©↓oduces a ring-shaped‌​←¶ sprocket chain, on which±≠♦ the bottle-bowl drive chain isλ↔∞ set to turn over the subjective factor, th♦♦≈e filling and sealing mechanism o ✘πf the above-mentioned glue p£δααart is connected with tε​" he transmission factor accord÷↓↓ing to the transmission belt, and the pressing π​→¶mechanism and the turni•∏ng mechanism depend on∑• the rotation. The capπ✘• sealing arm structure is asε‌​Ωsembled in the upper≈∏< support frame, the capping machine aΩπ→nd the automatic sealing machin≥↓e are assembled in the upper support frame by↕≥ the capping sealing ar≥ m structure, and the bπ≈≈‍ottle feeding organization is ¶≥∞₽placed on the feeding bottle swing rod↑≠§♦. An anti-backward wedge groove is sδ∞et up on both sides of the pendulum rod,​  and the automatic cover relea♦ se mechanism is placed a€πbove the support frame. The rλ≤©educer and the motor are asσ÷φsembled into a group, which is conn>'ected with the subjective factors. Th₹§e bottle channel support plate li×≥fting system is placed on th ​♠e lower support frame. A bot☆₹‌'tle lift support frame is set on it at equal®α→ intervals, the bottle transport channel is buπ☆ilt above the bottle lπ™ ‍ift support frame, and the bottle Ω<λ®is placed on the bottle transp ‌‍φort channel, close to the botφ∞tle feeding pendulum.

After the filling and seal ↑ing machine is used, it is also neε §cessary to pay attention to its ±±↕maintenance. When disas↔πsembling the piston rod an¥≤d the fixed screw, it is necessary to remove the↓✔₩ fixed screw during maintenanc♦∏e, so as to prevent da₹∏'mage to the processing technology of the other wh♥‍'en dismantling one. Regulation. Before cleaασ¥ning the piston machine filling and sealing •λ↓machine, the remaining product i≠™αnside should be remove♥→©±d, and then the barrel shφ±ould be filled with a mild cleaning solution. ®<The cylinder has been σ☆lubricated in the original factory, please do not✔​↑ open or add any grease to eπ§nsure the daily cleaning of¶÷" the surface of the sealing♦ ↔£ machine, and turn off th∏≠✔e power when it is not working.δ≈¶ In addition, in addition to persistent m∏α≈aintenance and proper application ofσ§↕∑ the filling and sealing mac♠σhine, inspection and adjustment should bφλ >e carried out on time. Only in this way can th÷γ€e sealing machine work in a healthy and healthy w₩ φay.

The automatic filling and sea∞α∑εling machine is different from the a>¶"♦utomatic sealing machine, that is, the small£↓↔  and medium-sized sealing machine♣​™ with manpower. The fully automatic canning i®♣s also fully automatic. ×±★Only the subsequent capping and boxing stage ♦‌is carried out by manpower, and©• the automatic sealing is pe•✔rformed by manpower. The key function of the↔Ω♥ tailing machine is canning, a λ €nd there are few addiα±×σtional functions. Unlike the au←βtomatic filling and seal≥★ing machine, it can at∞®tach a conveyor belt, a cap✔'ping machine, a marking mac★×hine, a boxing machine γ, and a fully automatic box→☆ sealing machine. Machines and other attached ma↕↕↑chinery and equipment.